BS1363-2 Temperature rise test device and the simulation panel
Purpose:
To check the maximum dimensions of the screw thread and dimension T1 minimum of E17 caps on finished lamps.
Testing:
When the cap on a finished lamp has been screwed into the gauge as far as it will go, the centre contact shall touch surface X. When the lamp is being removed from the gauge, at least two full turns shall be required to disengage the threads.
BS EN 1363-1 UK Plug Socket Gauge, BS1363-2 British Standard Plug and Socket-Outlets Gauge
BS1363 Uk Plug And Socket Gauge, British Bs1363 Plug and Socket Outlets Gauge
1. Application:
BND offers a wide range of gauge to meet the most common standards including those from IEC, EN, UL, GB, DIN, VDE and other similar international standards. Such standards require the checking of size & definition etc, these gauges are constructed from senior stainless steel and appropriate steel with a hardness of at least 60HRC and a roughness according to standard require.
British standards test gauge is strictly designed and manufactured according to the relevant standard requirements of BS1363-2.
This plug and socket test gauge is mainly used to test and inspect whether the structure and size of plugs and sockets conform to BS1363-2 standards. And the mainly application industries is electronics, electrical appliances, plugs and sockets and other similar areas.
2. Features:
Gauge dimensions, tolerances, material, hardness, surface roughness conform to the standards requirements;
Surface corrosion and abrasion resistance can resist normal contact corrosion and not embroidered patch (the operator hand may exist in the sweat, the corrosion effect equivalent to NACL salt solution or NH4CL salt solution corrosion);
Material hardness is more than 60HRC;
Material thermal expansion coefficient is small, dimensions and tolerances is stable and reliable.
It is designed according to the relevant provisions of BS1363-2.
It is used to check the technical parameters and size of plugs and sockets.
Concrete products:
1. Socket contacts gauge (BS1363Figure 12), it is a standard measuring device to check if it is connected as a test sample.
2. Socket do not contact gauge (BS1363-2 Figure 14): it is a standard measuring device to check if it is not connected as a test sample.
3. Transversal stress test gauge (BS1363-2 Figure 15): By simulating the bolt to insert into the socket test samples and imposing the prescribed weight force (poise) at the stated point to check whether the socket fits to the standard requirements.
4. Grounding minimum pull out force gauge (BS1363-2 Figure 16a): By simulating the grounding bolt insert into the socket test samples and imposing the prescribed vertical downward force (poise) to check whether the socket is fits to the standard requirements.
5. Diversion jack minimum pull out force gauge (BS1363-2 Figure 16b): By simulating the bolt of the firing line or zero line to insert into the socket test samples and imposing the prescribed vertical downward force (poise) to check whether the socket is fits to the standard requirements.
6. Socket and jack gauge (BS1363-2 Figure 11 or BS1363-1 Figure 11): Socket test samples through using the gauge to check whether the relative position of the hole, the size and depth of the hole, and whether the socket joint surface had fit to the standard requirements. There are two specifications of the go gauge, large and small.
7. Plug location and size gauge (BS13631 Figure 5). Plug test sample uses the gauge to check whether the relative position and the length of the pin as well as its joint surface with the plug whether it is fit to the standard requirements.
| Testing Gauge BS1363 British Standards Plug Gauges |
| Name |
Description |
QTY(piece) |
| BS1363-2-Fig1 |
Test PIN |
1 |
| BS1363-2-Fig2a.2b |
Elastic shell mechanical strength test device |
1 |
| BS1363-2-Fig 5 |
plug gauges |
1 |
| BS1363-2-Fig11 |
plug gauges |
2 |
| BS1363-2-Fig12 |
Contact test gauge |
1 |
| BS1363-2-Fig14 |
Non contact test |
1 |
| BS1363-2-Fig15 |
Insert transverse stress gauge |
1 |
| BS1363-2-Fig16 |
Insert pull-out force gauge |
2 |
| BS1363-2-Fig17a/b |
Temperature rise test device and the
simulation panel |
1 |
| BS1363-2-Fig19 |
Stainless steel solid fuse |
1 |
| BS1363-2-Fig23 |
Pressure test device |
1 |
| BS1363-2-Fig29 |
correction clamp |
1 |
| BS1363-2-Fig30 |
gauges |
1 |
FAQ :
What about your quality?
Each equipment must be carry out 100% examination and test again before shipping
What is the MOQ ?
Most instruments support MOQ one set.
How long the delivery time ?
Generally most equipment will be 3-10days after we receive your payment or the order conformed ,please conform with us before you made an order .
What is the warranty of the products?
One year ,but we can provide you life long support .
What is the package?
Export standard Solid wooden case
What is the shipping way ?
We have stable forwarding agent for air and sea transportation ,and also express about DHL TNT etc , we will suggest you the best shipping way base on your requirement .
What is the payment term ?
T/T, Western Union,Money gram ,Paypal etc
Company Profile :Our Advantages :
Certifications :Factory Introduction :Plant Warehouse :Cooperative Customers & Brands:
Customer Reviews :Product Packaging :
Audited Supplier 
){kind=link}